![]() ![]()
![]() I use a Mac, so to take a screenshot I use the Shift+Command+4 shortcut then, using the mouse, I highlight the area I want to snap. Saving all the critical measurements: Once I have an outline and rocker profile I’m happy with in Aku Shaper, I take screenshots of all the important points and their measurements – 1’ from tail and nose, wide point, nose & tail rocker etc. #GET OUTLINE FROM IMAGE AKU SHAPER FREE#I also use the free FinFoil application to muck about with fin designs, but that’s another story for another day.Ģ. Because I haven’t done enough playing yet to go into too much detail about Shape3D, for now I’ll stick to Aku Shaper. The other application I’ve recently started playing around with is Shape3D, on the advice of local shaping legend Leighton Clark, whose shaping machine runs on files created through this program. However, I’ve developed a workaround for this, which I’ll detail at a later point in this post. The downside is that with the free version, you can’t save your shapes. It takes a bit of playing around to get used to the controls, but it’s pretty intuitive. #GET OUTLINE FROM IMAGE AKU SHAPER TRIAL#The free trial version of Aku Shaper is the one I’ve used mostly. To date I’ve used two different programs for this process. I’ll then sit down with my laptop and, using a free board shaping application downloaded from the internets, I’ll set about conceptualising the outline, rocker curves and foil of the board. a 5’10” quad fish with a beaked nose and single to double concave bottom contours. They start in my head as an idea of the board I’d like to create – e.g. Designing the outline: So far all the boards I’ve built have been unique, one-off shapes. Feel free to cherry-pick any bits that you find useful.ġ. What I’m going to detail here is my process for creating a template. These days it’s much more likely that the design process starts on a computer screen and in many cases it doesn’t venture beyond the digital realm until the machine-shaped blank is ready for cleaning up.īut that’s not what I’m going to talk about here. In the “olden days” before the advent of computer aided design, shapers relied on some more analogue methods for creating their templates – bending and tracing flexible batons into aesthetically pleasing curves, combining existing templates to form new shapes, and others that I won’t go into detail about here. This is laid onto the blank down the centre and traced, then flipped and repeated on the other side to ensure symmetry (if that’s what the shaper is aiming for). #GET OUTLINE FROM IMAGE AKU SHAPER FULL#Your basic template is a full length rendering of the board’s outline, divided in half lengthwise. The proven vehicle for this stage of the process is the Template. Most beginner shapers have a reasonably good idea of the board they want to shape, but aren’t always confident about getting the shape from their head and onto the blank. Every shaper has their own unique process for building a board – from developing the concept of a board in their imagination, to getting it shaped, wrapped in fibreglass and onto the wave. You can find Aku Shaper here.īlanks are on the way.should arrive sometime next week.There are almost as many methods for shaping surfboards as there are shapers. #GET OUTLINE FROM IMAGE AKU SHAPER SOFTWARE#If not, you'll have to settle for the free software (and find someone with the machine). Also, if you have $65,000 lying around, you can buy the Aku machine and have it cut your CAD board designs for you. I think there's a newer version of the Aku Shaper coming out soon which will feature a 3D viewer. I dunno if I'll make a rocker template, but I did the profile outline just for fun. In any case, here are some screenshots of what I have so far. I think I need to fiddle with the printer margins or something cause I'm getting only 1/4 of the board. I'm having trouble printing the outline onto paper which I'll then tape together to end up with the final outline. I'll then try to scale it down using Greg Loehr's "1/8" formula to come up with something a bit shorter and thinner. I spent the greater part of last night making a board file by tracing a picture of the Brom fish. ![]() The software is not exactly the most intuitive thing to use (even for a computer guy like myself), but the interface is fairly simple and easy to figure out with a little time. I've decided to try my hand at the Aku Shaper software to create an outline/template based off of my Brom fish. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |